AQUA PU 17-06 (FLOSIL PU 17-06)

High Performance Polyurethane Coating

Product Description

A two-component modified ester polyol aliphatic polyurethane coating, designed to provide excellent weathering resistance for longer colour and shade retention. Exhibits excellent UV resistance, water resistance and recoatability.

  • Extensive Applications
  • High Aesthetics
  • Excellent weather proof and UV Resistance
  • Low Permeability
  • Easy to maintain, Durable
  • Extensive Range of Colours
Colour All RAL, BS colour
Finish Gloss, Semi-Gloss, Matt
Volume Solids 50 ± 3%
Mixing Ratio 9:1 (Part A : Part B)- By volume
Pot Life 3 – 4 hours @ 30°C
Typical Film Thickness 50μ dry
Theoretical Coverage 10.5 Sq.m /liter at 50μ DFT
Method of Application Airless spray, Conventional Spray, Brush, Roller
Touch Dry 30-60 minutes
Dry to Handle 4-6 hours at 30°C
Hard Dry 12 hours at 30°C
Full Cure 7 days
Minimum Over-coating Period 4 hours
Maximum Over-coating Period 72 hours
Surface should be clean and dry prior to over-coating.

Systems and Compatibility

  • Can be applied as finish coat on AQUA MASTIC, AQUA ST, AQUA ST-03, AQUA SEALER.
  • Please consult Flosil-BET Coatings (India) Pvt Ltd for further product recommendations.
Abrasion Resistance Max 90mg weight loss per 1000 cycles - 1kg load - CS10 Wheel - ASTM D4060
Impact Resistance 27 Joule - ASTM D2794
Pull - Off Adhesion 10.66 Mpa - ASTM D4541
Scratch Hardness 12.5 kg Load - No Failure - (BS3900 Part E2)
Salt Fog Resistance Excellent, Unaffected after 2000 hr Exposure - ASTM B117
Cyclic Fog / UV Exposure Excellent, Unaffected after 2000 hr Exposure - ASTM 5894-05

Possible Applications

Aqua PU 17-06 is suitable for use in both new construction and as a maintenance coating which can be used in a wide variety of environments including offshore structures, chemical and petrochemical plants, bridges, pulp and paper mills, and in the power industry.

Air Temperature 5-55°C
Substrate Temperature 5-65°C
Relative Humidity 50% minimum, 85% maximum
Surface temperature shall always be at least 3°C above Dew Point. Do not expose the coated articles where there are chances of condensation on the surface.

Surface Preparation

All surfaces to be coated shall be dry and free from oil, grease, dust, dirt and any foreign matter that can adversely affect adhesion of coating. Solvent cleaning as per SSPC SP1 shall be conducted wherever necessary.


Aqua PU 17-06 is supplied in 2 parts. Always mix curing agent (Part B) into the liquid binder (Part A) while stirring. 75-100 RPM mixer is recommended. Material should be screened prior to application.


Aqua T02 - 10 to 20% as Needed

Airless Spray

Recommended, Tip range: 0.43-0.53 mm at 2500 - 3000 psi tip pressure. Remove filters from the spray equipment to avoid blockages

Conventional Spray

Recommended. Do not exceed spray pressure more than 4 Kg/Sq.Cm. Remove filters from the spray equipment to avoid blockages.

Brush / Roller

Recommended to use roller and brush.

  • Available worldwide through Flosil -BET Coatings (India) Pvt Ltd.
  • Packing Size = 4 Liters.
  • Shelf Life: 12 Months* from the date of manufacturing

*Material to be stored in sealed and unopened containers in closed shelter.


Effluent Treatment Plant before Aqua ST & PU 17-06 application

Effluent Treatment Plant after Aqua ST & PU 17-06 application

Before application of Aqua ST & PU 17-06

After application of Aqua ST & PU 17-06


No:40, Velichai Village,
Vandalur – Kelambakkam Road,
Chennai – 600 048.