Colour	All RAL, BS Colour or as per sample
Finish	Glossy
Volume Solids	100%
Mixing Ratio	5:1 (Part A : Part B) By Weight
Typical Film Thickness	100 - 200 μ dry (Please consult Flosil-BET for dry film thickness depending on (application)
Pot Life	30 minutes at 30° C
Theoretical Coverage	10 Sq.m / liter at 100μ DFT
Method of Application	Airless spray, Roller, Brush
Touch Dry	2-3 hours at 30° C
Dry to Handle	24-36 hours at 30° C depending on thickness
Hard Dry	12 hours at 30° C
Full Cure	7 Days depending on thickness

Minimum Over-coating Period	4 hours at 30° C
Maximum Over-coating Period	12 hours at 30° C
Maximum Over-coating Interval	Unlimited
Surface should be clean and dry prior to over-coating. If Aqua PU has been exposed for long periods, fresh water washing should be conducted before application of any coatings.

Systems and Compatibility

• Can be applied as finish coat on following products - ,Aqua ST-03, Aqua ST, Aqua Mastic.
• Can be overcoated with the following products - Aqua PU, Aqua PU 17-06.
• Please consult Flosil-BET Coatings (India) Pvt Ltd for further product recommendations.

Abrasion Resistance	Max 20mg weight loss per 1000 cycles - 1kg load - CS10 Wheel - ASTM D4060
Impact Resistance	27 Joule - ASTM D2794
Dry Heat Resistance	150° C - ASTM D2485
Pull - Off Adhesion	12.55 Mpa - ASTM D4541
Scratch Hardness	12.5 kg Load - No Failure - (BS3900 Part E2)
Salt Fog Resistance	Excellent, Unaffected after 4500 hr Exposure & continued till 10000 hr - ASTM B117
Cyclic Fog / UV Exposure	Excellent, Unaffected after 4200 hr Exposure - ASTM 5894-05

Surface Preparation

Aqua Sealer is highly flexible coating in terms of surface preparation requirements. Surface preparation may differ according to the final exposure or application of Aqua Sealer. Refer to Flosil-BET for recommendation on required surface preparation

Mixing

Aqua Sealer is supplied in 2 parts, a liquid binder (Part A) and a liquid binder (Part B). Always mix liquid (Part B) into the liquid (Part A) while stirring. 75-100 RPM mixer is recommended. Material should be screened in a mesh prior to application.

Thinning

Not Recommended. Use Aqua T01 only for cleaning of equipment.

Airless Spray

Recommended, Tip range: 0.48-0.63 mm at 3500 - 4000 psi tip pressure.

Conventional Spray

Recommended. Do not exceed spray pressure than 4 Kg/Cm2. Remove filters from the spray equipment to avoid blockages.

Brush / Roller

Recommended to use roller and brush.

Air Temperature	5-55° C
Substrate Temperature	5-65% C
Relative Humidity	50% minimum, 85% maximum
Surface temperature shall always be at least 3°C above Dew Point. Do not expose the coated articles where there are chances of condensation on the surface.

• Oily surfaces
• Condensed surfaces
• Wet/Damp units
• Fire rated Class I – does not allow flame spread (Self-extinguishing)
• Underwater applications
• Storage/Drinking/potable water tank & pipe lining -interior & exterior

Availablity & Packing Size

• Standard Packing Size = 16L Mix Paint.
• Smaller pack sizes may be available on request.
• Shelf life: 36 months* from the date of manufacturing.

*Material to be stored in sealed and unopened containers in closed shelter.